Mahr M1 Perthometer

Pick-ups for multiple measuring tasks for the use with PFM/PFM 2

The pick-ups of type N are

characterized by special construction

features:

*Stylus tip geometry as per EN ISO 3274, standard 2µm/90° (80 µin/90°)

*Measuring force of approximately 0.7mN (1.95 mozf) (as per EN ISO 3274)

*Reliable inductive converter

*Rugged, rigid housing

*Self-aligning, elastic bearings

*Reliable plus and socket connections

The standard NHT 6 pick-up

for example, adapts to various surface to be traced due to the special design of its tracing arm and skid. Further pick-ups such as the NHT 11 are suited for recessed measuring points and grooves.

NHTR-100 pickup

Order #6111508

Single-skid pick-up with lateral, spherical skid, radius 0.3 mm in traversing direction, stylus radius 5 µm (200 µin), 90° suitable to measure inner radii in circumferential direction with a diameter larger than 12 mm (.472") (without figure).

The NHTF 0.5 for gear tooth flanks

enables roughness measurements even at hardly accessible points.

NHT 6-100 pickup	Order # 6111501
Type	single skid pick-up with spherical skid
Skid Radius	25mm (.984 in) in traversing direction, 2.9mm (.114 in) at right angles
Contact Point	0.8 mm (.0315in) in front of the stylus
Measuring range	100µm (.00394 in)
Specification	for plane surfaces, bores with a dia. larger than 6mm, (.236 in) and a max. depth of 17 mm ).669 in), grooves with a width larger than 3 mm (.118 in): a width larger than 3 mm (.118 in): min. workpiece length + traversing length + 1 mm (.0394 in)

NHT 6-150 pickup	Order # 6111504
Type	single skid up with spherical skid
Skid Radius	25mm (.984 in) in traversing direction, 2.9mm (.114 in) at right angles
Contact Point	0.8 mm (.0315 in) in front of stylus
Measuring Range	150 µm (.00591 in)
Specification	for plane surfaces, bores with a dia. larger than 6mm, (.236 in) and a max. depth of 17 mm ).669 in), grooves with a width larger than 3 mm (.118 in): a width larger than 3 mm (.118 in): min. workpiece length + traversing length + 1 mm (.0394 in)

NHT 11-100 pick-up	Order # 6111505
Type	single-skid pickup with spherical skid
Skid radius	25 mm (.984") in traversing direction, 2.9 mm (.114") at right angles
Contact point	0.8 mm (.0315") in front of the stylus
Measuring range	100 µm (.00394")
Specification	for plane surfaces, bores with a diameter larger than 11 mm (.433") and a max. depth of 14 mm (.551"), grooves with a width larger than 2.5 mm (.0984") and a max. depth of 7.5 mm (.295")

NHT pick-up extension (80 mm/3.15"), Order # 6850530

(for pick-ups of the "N-series")

NHT 3-100 pick up	Order # 6111502
Type	Single skid pick-up with spherical skid
Skid radius	25mm (.984 in) in traversing direction, 1.45mm (.0571 in) at right angles
Contact point	0.9 mm (.0354in) in front of the stylus
Measuring range	00 µm (.0039 in)
Specification	For bores with a diameter larger than 3 mm (.118 in) and a maximum depth of 17 mm (.669 in). Minimum workpeice length + traversing length + 1 mm (.0394 in)

NHTF 0.5-100 pick up

Order # 6111503

Type

Single-skid pick-up with spherical skid

Skid radius

25mm (.984 in) in traversing direction, 1.45 mm (.0571 in) at right angles

Contact point

PFM 2 drive unit

Traversing direction	transverse
Traversing lengths	set on the perthometer
as per DIN/ISO	1.75mm, 5.6mm, (.07 in, .22 in)
as per EN ISO 12085	1mm, 2mm, 4mm, (.0394 in, .0787 in, .157 in)
Traversing speed	0.5mm/s (.0197 in/s)
Dimensions	dia. 24mm (.945 in) L=112mm (4.41 in)
(w/o pick-up protection

PFM 2 set Order # 6720909

consisting of:

PFM drive unit

VEE pick-up protection

Pick-up protection

Screwdriver

Applications with PFM Drive Units

Accessories

PP vee-block Order # 6710401 with four different prisms for mounting axis-symmetrical workpieces with diameters from 1 mm to 160 mm (.0394 in to 6.30 in). Dimensions (LxWxH) 100mm x 80mm x 40mm (3.91 in x 1.58 in). Weight 1.5 kg (3.31 lb.). Including clamping springs for holding light workpieces in the prism.

XY table CT 120 Order # 6710529 for mounting and aligning workpieces. Can be adjusted in two coordinates by 15mm (.591 in). Table surface 120mm x 120mm (4728 in. x 4.728 in) with two brackets.

PPS parallel vice Order # 6710604 for mounting rectangular and cylindrical workpieces. Jaw width 70mm (2.76 in), jaw height 25mm (.984 in), span 40mm (1.58 in), total height 58mm (2.28 in). Weight 2 kg (4.41 lb).

Shaft whippers for PFM 2 for diameters from 5mm to 80mm (100mm) (.197 in to 3.15 in/3.94 in) Order # 6850738 Roughness measurements on workpieces which are still being manufactured require particular device for solving the measuring task (e.g. transverse tracing on crankshaft or camshafts).

Mahr or DKD calibration certificates are available on request.

PRN 10 roughness standard Order # 6820420 with Mahr calibration certificate. Roughness standard with turned profil, chromed. Profile depth approx. 10µm (.394µin). For checking the roughness measuring station.

PGN 3 geometric standard Order # 6820601 (w/o figure) Surface roughness standard with a sinusoidal froove profile. Profile depth approx. 3µm (120uin), groove spacing approx. 0.12mm (.00472 in). For checking the roughness measuring station.

The Perthometer Sets for Mobile Operation

Perthometer M1 set Order # 6910134

Perthometer M1 set with 2008143 patch Order # 2190827

The Perthometers of the M series are delivered as a set in a handy carrying case. The instrument is thus safely packed for transport. The components included in the set can be easily and quickly be assembled to form a complete measuring station.

Rapp Industrial Sales * 127 Main Street * Connoquenessing, Pa 16027

Phone 888-789-7277 * 724-789-7853 * Fax 724-789-7288 Email: sales @rappindustrialsales.com

0.6 mm (.236 in) beside the stylus

Measuring range

100 µm (.00394 in)

Specification

For gear tooth flanks with a modulus larger than 0.8.

Decription

This instrument serves for determining and documenting the most common parameters as per DIN EN ISO/AMSE/prEN 10049 (Ra, Rz, Rmax, and RPc) and according to the JIS Japanese standard (Rz, Ra).

With a minimum of keys, the Perthometer M1 is characterized by a multitude of functions. An automatic function enables periodic and aperiodic profiles to be identified and the cutoff to be set according to standards without any prerious test measurement, such that unintentional non-standard measurements are excluded.

In mobile use, the measuring record can be output on the built-in thermal printer automatically or simply by pressing a key. Stationary operation offers the possibility of connecting the Perthometer directly to a PC via the serial interface.

Delivery as a set in a handy carrying case.

Perthometer M1 set Order No. 6910134

Perthometer M1 Set with 2008143 Roughness Master Order No. 2190827